Kann gescrollt werden
| Outline | I/O | Inputs | TOTAL 10ch : Mono (MIC/LINE):4, Stereo(LINE):3 |
|---|---|---|---|
| Phantom power | CH1, 2 : +30 V | ||
| Outputs | SPEAKERS [L, R], MONITOR OUT [L,R], SUBWOOFER OUT | ||
| Control and others | FOOT SW : Effect Mute on/off | ||
| Bus | Stereo: 1, Effect: 1 | ||
| Input Channel Function | PAD | 26 dB (CH1-4) | |
| Hi-Z | Supported (CH4) | ||
| EQ HIGH | 8kHz +15dB / -15dB | ||
| EQ MID | 2.5kHz +15dB / -15dB | ||
| EQ LOW | 100Hz +15dB / -15dB | ||
| On-board processors | DSP | SPX Algorithm Reverb 4 programs, MASTER EQ (SPEECH to MUSIC), Feedback suppressor | |
| On-board amplifiers | Maximum output power @4ohms | 1kHz THD+N less than 10% (CEA2006) : 250 W + 250 W, 1kHz THD+N less than 1% : 110 W + 110 W | |
| Maximum output power @8ohms | 1kHz THD+N less than 10% (CEA2006) : 170 W + 170 W, 1kHz THD+N less than 1% : 110 W + 110 W | ||
| Level Meter | 6points (-20, -6, 0 , +3, +6, LIMITER) | ||
| General specifications | Frequency response | Input to SPEAKERS : +1 dB/-4 dB (40Hz to 20kHz), Input to MONITOR OUT : +0.5 dB/-1.5 dB (20Hz to 20kHz) , refer to the nominal output level @ 1 kHz | |
| Total harmonic distortion | Input to SPEAKERS : 0.2 % @ 13.8 W (40Hz to 20kHz), 0.4 % @ 23.2W (1kHz), Input to MONITOR OUT : 0.05 % @ +10 dBu (20Hz to 20kHz) 0.009 % @ +20 dBu (1kHz), (THD+N, Measured with 22 kHz LPF) | ||
| Hum & noise level | Equivalent input noise | -115 dBu | |
| Residual output noise | Input to SPEAKERS : -68 dBu (40Hz to 20kHz, MASTER: min), Input to MONITOR OUT : -99 dBu (20Hz to 20kHz, MONITOR: min) | ||
| Crosstalk | -80 dB (1 kHz, Measured with 1 kHz band pass filter) | ||
| Protection circuit | Load protection | DC-fault | |
| Amplifier protection | Over heat protection, Over current protection | ||
| Power requirements | AC 100-240V, 50Hz/60Hz | ||
| Power consumption | 35W (Idle) / 90W (1/8 Power) | ||
| Dimensions | W | 375 mm (14.8") | |
| H | 147 mm (5.8") | ||
| D | 220 mm (8.7") | ||
| Net weight | 4.2 kg (9.3 lbs.) | ||
| Accessories | Owner’s Manual, Technical Specifications, Power Cord (2m) | ||
| Options | Foot Switch: FC5, Mic Stand Adaptor: BMS-10A, Rack mount kit RK-EMX2 | ||
| Others | Operating Temperature : 0 to +40℃ | ||
Analog Input Characteristics
Output Characteristics
*Tip = HOT, Ring = COLD, Sleeve = GND
**Tip = Positive, Sleeve = Negative
